My stove has been running since Jan 12. A while back I had some noise suspected fan bearings then it quit making noise. Yesterday I came home and stove was off, Fired up fine but I discovered later fan was running slow and hot. Shut down and used a box fan to cool it down. Glad I researched and had a new set of bearings here. Took about an hour to replace them. Boy what a difference really puts out heat! Thanks to everyone here for the great amount of knowledge.

I have been using pro pellets or magic sparkle from fiber byproduct White Pigeon Mi. Heat good no feed problems and easy to get at Rural King or Menards. Stove has been running since Jan 12 almost non stop and house is warm much better than LP. Highest setting has been level 6. I think it will work even better when I get 2.71 installed.

Steady
I'm up North near Angola. Tonight getting close to 7 degrees stove is on number 5 tonight putting out good heat:cheer: Seems to be easier to tune when the air is crisp and cold with calm wind. Next will be getting 2.71 installed and loop feed wheel gasket. Hope I can find another stove locally like this one.

Thanks Steady
I got it dialed in very cold here in Northeast Indiana. Running level 4 at night had 5 this evening. It is 9 degree now at 10:30 pm Did not hear the LP furnace come on this evening but house is still more comfortable. And when the pot was full of pellet it looked rich lazy yellow flame I turned up exhaust until the pot cleaned itself. Then made small adjustments now looks real good. I'm sure Saturdays wind did not help.

Thanks
When I cleaned it I found the feeder wheel gasket worn ragged so I turn it over for now. Pellets are hard on it! I think this stove has only had pellets. Last night the weather changed and it was extremely windy. I found the pot full to the top I increased the exhaust blower to get them back down but it has taken a while for me to get it adjusted today. Cold enough I had to turn it up to #5 first time for that. Had been running on 2 and 3.

Ran the stove last Sunday to this Saturday. Looks like a cold front coming so shut down to clean and modify the exhaust. Worked good all week level 2 or 3 house is warm and lp furnace has run about 2.0 hrs all week :)I have been burning the hardwood pellets from fiberby products in White Pigeon Mi. Seem to burn good and clean, a little concerned about saw dust build up at bottom of hopper at the feed wheel. Very impressed with the stove. Has a cracked door glass so I sealed the inside with clear hi temp silicone sealer to keep air out of stove. Will try to get it fixed after cold weather. be fore the down load site went down I got bixcheck 080315.zip and the manual and 02060021 do I need another file for the 2.71 version? And thanks this group has been very helpful. If I see a deal on another stove I would buy!

Ok I got it installed and running yesterday. On heat level one I thought boy does that heat! Lit right up with no problem. I would like to get the latest software I believe it has 2.06 ash dump run 3 cycles with a pause each turn. Not quite sure what my flame should look like? But it did run perfect all night

I've been looking it over does not look like it was used much very clean.Pulled the ash door and there is a small amount of soot so I believe it was pulling exhaust back in. can I just modify my cap by put the exhaust straight out about 3 ft leave the cap on for cold air?

Ok so can I put the exhaust straight out the wall? I dont have to come out and go up?

I got the stove home tonight. Looks to be in good shape very clean has only burnt wood pellets.Pipe all looks like new. It does look like there is some soot on the air intake of the cap like it pulled exhaust back in the air intake? Anything I should look for before installing?

Well I took a chance and bought a 115 with the exhaust pipe. Anything I should do when moving it and hooking back up? Also can I hook a remote thermostat up?

I'm looking at a used dc 2000 looks to be in good shape but it does not turn on. Is there a manual to trouble shoot the problem? Are these good stoves? Had someone tell me you could never get him to give his up. He loved it.

Hi new here but have a question. Looking at a used 115 has been used 2 seasons needs 1 igniter and door glass is cracked. I like the design and software features of this stove. Price is about $500 including pipe. I live on a farm are there grains I can grow other than corn that would burn good? Should I buy?
Thanks