Haven't been hanging around here much lately, If you need one yet please pm or email ccbarton@charter.net.

We use a 10" butterfly damper on our Fahrenheit units. $29 if you want one and can't find it locally.

Do you have the Manual for the furnace. There is a lot of troubleshooting info in there.

Farmich, I know corn is high, but it is not 320 a ton yet, is it?

I think there is nearly 36 bushel to a ton, so at 6.50/bu a ton is 234.00 which is about what softwood pellets are here in WI.

I got both the FPI DellPoint and the Paromax here. If you search my posts you will find out what it takes and nothing has changed except the prices. Gone up of course.

I might check that out because you never know when you may need something for your demisic or even if you have one.
thx stinger

In our area Fleet Farm has the grade of dura-vent venting that has the rope gasket. We handle the dura-vent brand Pellet vent pro line which has the laser welded seams and the neoprene O-ring gasket.

I have found Fastenal to be spendy. Other places have it for one/half that amount.

Has anyone burned or installed one of these units (Hydroflex 60) yet. What can you share with us.

Hi Dennis, It seems like all the gearboxes get that way in time, why the lubricant doesn't do the job I don't know.

We run the wire from the motor frame to the ground wire post on the removable panel by the control panel.
This has been recommended by Claude at Paromax.

We normally have the motors in stock.

If anyone is in need of Traeger parts, Lulloffs True Value at Kiel, Wi (about 40 miles south of "Titletown" has quite a few available. 920-894-3236

If you are in WI there is a Good Dealer about 40 miles south of "Titletown" at Kiel, WI.
Call Joel at Lulloffs True Value 920-894-3236

We have been selling/servicing the F50 for two years and found the best source for info to be the factory because they are familiar with all the models/changes/modifications.
I am hesitant to post my cell# but would welcome ?? here. Which version/mfg date do you have?

Clair

Good evening, lowcostheat here.

The 16 pin or 20 pin control panel is $483 with shipping.

If any of you are looking for repair/replace parts, we can help you. We sold the FPI product and now the Paromax.

We have many Dellpoint parts in stock for 2 day shipping. Send a private message please because I am not on here every day.

Lastly, I am biased, but I think the Dellpoint is the best bang for the buck in performance and dependability.

We service all pellet stoves when customers call and their dealer went out of business or quit selling the brand.

That is the way they are assembled. Gravity keeps them in nearly one place.
We have sold them since 06 and never needed to service the auger feed motor mounting.
Grounding the motor/gearbox has been reccomended by the new/old manufacturer (Paromax)

Did I read someplace where a stove was run for four years and the fans had not been cleaned? and the stove had a vibration?

At least it came with a confession, dealers appreciate that :o)

We do use the thermostat setting, (fuel miser) the furnace runs at the lowest setting for 59 minutes or until heat is called for again.
The Honeywell focus pro 6000 is what we used.
Set back t-stats are not my favorite because of the time required to bring everything up to max heat.

Nice compact furnace, fits through doorways and in spaces many will not.

Oh sure, every day when we need heat. Do you have one? Having problems? or just want to learn more about the lowest operating cost heating appliance?

Members/readers/interested parties. If anyone has questions/suggestions RE the Europa units, I or some of the other DP owners/dealers that regularly hang out here may be able to help. We have sold/serviced the FPI Europa as well as the newer Paromax Europa and still have units and parts available.

Have a safe warm winter season.